Showing posts with label Fomapan 200. Show all posts
Showing posts with label Fomapan 200. Show all posts

Sunday, 4 February 2024

127 Day January 2024

Kodak Baby Brownie with Fomapan 200

Last weekend's 127 Day provided an excuse to use the Kodak Baby Brownie, the subject of my previous post. I had cut down two rolls of medium format film to 127 size and rolled these with the appropriate backing paper and spools: one roll of Kentmere Pan 400 and one of Fomapan 200. I shot the Kentmere Pan 400 first, then the Fomapan 200, but developed them in the reverse order. The lighting conditions had been light cloud giving way to hazy sunshine. When I took the roll of Fomapan 200 from the tank, the negatives looked very thin, something that I had noticed with the film shot in the Baby Brownie last summer. With hazy sunshine, and a nominal exposure of 1/50th at f16 (or however close to this the Baby Brownie's aperture and shutter speed are), a 200 ISO film should have given adequate results. Although a stop faster, given that the lighting was perhaps a little less bright for the Kentmere Pan 400, I extended development time to push it another stop. 

Kodak Baby Brownie with Kentmere Pan 400

The results from the Kentmere Pan 400 were much denser, and this push was probably unnecessary. I had used Kodak HC-110 for both films; a little research online reveals lots of comments about Fomapan 200 and HC-110 not being a good combination. I had used the times from the Massive Dev Chart, and when subsequently developing another roll of Fomapan 200 (not from the 127 Day), I pushed this a stop, and the results were much better (it would probably be preferable to rate the film a stop lower instead however).

Another aspect of using the camera again was checking the lens' angle of view.I had suspected that this was wider than the viewfinder–probably to give the casual user a margin of error not to lose heads from the top of the frame–and took a couple of photographs with this in mind, particularly the one below. Here the shot was framed with the second pillars from the centre at the edge of the viewfinder, demonstrating that the actual shot is notably wider than what the viewfinder does show, although one wouldn't chose a Bakelite box camera from the 1930s or 40s if accuracy was really important, but worth bearing in mind.

Kodak Baby Brownie with Kentmere Pan 400

I had a few problems with development thanks to the slightly uneven cut edge of the film: the Kentmere Pan roll was a little taller once cut to fit well into the developing spiral, causing a little buckling and a few section of negatives not processing properly due to contact while developing. This also created a bit of a 'fat roll' with some light leaks as a result. By contrast the Fomapan cut much more smoothly, but scratched more easily in the process of being cut down, due I think to the emulsion being softer, and possibly the film substrate too. The thin negatives of the Fomapan film in combination with the choice of subject–as in the image at the top of this post–was vaguely reminiscent of Pictorialist landscape work, something not entirely unsympathetic in the use of a camera such as the Kodak Baby Brownie.

Kodak Baby Brownie with Kentmere Pan 400

Kodak Baby Brownie with Kentmere Pan 400

Kodak Baby Brownie with Kentmere Pan 400

Kodak Baby Brownie with Fomapan 200

Kodak Baby Brownie with Fomapan 200

Kodak Baby Brownie with Fomapan 200

Saturday, 27 January 2024

Kodak Baby Brownie

Kodak Baby Brownie

The emergence of plastic in the manufacture of cameras from the late 1920s into the 1930s allowed for the typical shape of the snapshot camera to radically change. The Kodak Baby Brownie with its Bakelite body, updates the simple, entry-level box camera. One imagines that it looked very modern when first produced, in comparison to Kodak's typical box camera, which only recently would have been made with a cardboard body. The Kodak Baby Brownie owes its distinctive styling to Walter Dorwin Teague who designed many cameras for Kodak: the vertical ribbed designs that run around the camera with the central roundel of the lens makes it a little reminiscent of an Art Deco radio set, while the curves and scalloped edges evoke light wooden furniture, a bureau or a cabinet perhaps. It was not Kodak's first plastic camera–according to Art Deco Cameras, Kodak Ltd in the UK had that honour with the No. 2 Hawkette–the Hawkette however was made for promotional purposes, not for general retail; according to numerous sources, 4 million Kodak Baby Brownies were produced over the two phases of its production either side of the Second World War.

It appears that the rationale behind the design of the Kodak Baby Brownie was Kodak's desire to return to the $1 price point of the original Brownie camera of 1900 (it's worth mentioning that this does not of course account for the effect of inflation over the thirty-odd years–a single dollar must have bought a lot more in 1900 compared to 1934, when the Baby Brownie appeared; the low price of the camera presumably reflects the economies of scale possible with Kodak's manufacturing in the mid-thirties). The Kodak Baby Brownie is simpler than the original Brownie too, partly due to the plastic construction. The meniscus lens is fixed-focus, with a fixed-aperture, and the rotary shutter has a single speed. Most sites profiling the camera do not usually provide lens and shutter specifications: Art Deco Cameras lists the lens' focal length as being 60mm, its aperture as f16 and the shutter speed at 1/50th; the manual states that "everything about five feet and beyond will be photographed sharply". It takes 127 format rollfilm, smaller and cheaper than 120, appropriately for a cheap camera appearing during the Depression, although it does use the 'full-frame' of the 127 format, nominally 4x6cm, giving eight exposures on a roll of 127 film–other cameras had already created the 'half-frame' 3x4cm negative size, which provides sixteen frames on a roll.

The Kodak Baby Brownie had two distinct periods of production. Kodak manufactured the Baby Brownie in the US until 1941; subsequently, Kodak Ltd in the UK made the camera between 1948-52. Given that there appears to be no observable differences between the US and UK made Baby Brownies, one wonders whether the dies and moulds were shipped out to the UK after the Second World War to boost the Kodak Ltd's postwar production, with the Baby Brownie, coming of the Depression, now a fitting camera for Austerity Britain, still in rationing. There was a slight variant model Kodak Baby Brownie for export, distinguished by a metal stud or pin above the lens. This is a 'time' setting: pull the stud out, and the shutter stays open when the shutter lever is pressed. The Brownie Camera Page states that this export version was made in the UK during the camera's second production run; my camera has the time setting, although the lettering on the bottom of the camera clearly reads "MADE IN USA". If exactly the same moulds were used for the UK-made camera (the time setting requiring a single small hole to be drilled through the front), this might explain this discrepancy, although I would have thought that any camera made in the UK would have to be marked as such. As well as the 'export variant' there was also a commemorative version made for the 1939 New York's World Fair, which has a rectangular name plate around the lens with this lettering: the camera itself has 'BABY BROWNIE' embossed around the lens.

Kodak Baby Brownie with viewfinder raised

I bought my Kodak Baby Brownie at the Place du Jeu de Balle flea market in Brussels in late spring last year for €10, haggled down from €15 (there were many other cameras there, but I was on a tight budget after a week abroad, and knowing that there's usually very little that can go wrong with a simple box camera, the Brownie seemed a safe investment). I used it last year on the 127 Day in July, but did not scan the negatives at the time, a couple of which illustrate this post below. When I bought the camera I wasn't aware of the export variant, but was pleased that was what I had, a small difference which does increase the conditions in which the camera can be used–although with some caveats, mentioned below. The modest size of the camera, with its curved and ribbed shape, as well as the Bakelite itself, does feel good in the hand, perhaps rather like an over-sized netsuke.

To open the camera for loading and unloading film, on the camera's base is a metal lever which pivots between OPEN/CLOSE (and sweeps over lettering stating the camera was made in the USA). The top slides out from the body with the film carrier attached. Opening the camera shows how simply it is constructed despite its Art Deco stylings: the camera is made from three pieces of Bakelite, the body, top plate, and film carrier, with a few metal fixings.

Kodak Baby Brownie - opened for loading

The the camera has a curved film plane, a common strategy to compensate for the limitations of a simple meniscus lens. The inside moulding is ribbed behind the lens inside counter reflections on the smooth Bakelite surface. One can also see that there's a metal stop behind the lens to reduce its aperture and increase definition, another frequent compensation for the limitations of a simple lens. The film spools are held either side of the lens opening on the film carrier by a sprung metal clip, with an additional piece of sprung curved metal on the supple-side to prevent the film from unspooling. Manual frame advance uses the red window in the middle of the camera back.

Kodak Baby Brownie - opened for loading

The rotary shutter on my camera has some rust as can be seen in the image below. To trip the shutter, the lever has to be pulled to the left from the user's position; it springs back into position with a self-capping function. The time setting works by simply blocking the shutter from completing its swing when the pin or stud is pulled out. The shutter lever needs constant pressure for the shutter to remain open: it will close when the shutter lever is released, or if the time pin is pushed back in. Framing is achieved by a fold-up open frame finder on the top of the camera body.

Kodak Baby Brownie - detail of shutter mechanism

My camera had some damage to two opposite corners, showing the fragility of the Bakelite: the chip on the inside rear corner I thought might possibly cause a light leak, which can be seen in the image above. To counter this, I added a small strip of black tape on the inside of the body. Using the camera for July 2023's 127 Day, the few frames from the Kodak Baby Brownie show that the lens has fairly good definition in the centre of the image, but this does fall off considerably towards the edges. When the camera was produced, most photographs for the typical user would probably have been made as contact prints and the limitations of the lens less apparent.

Kodak Baby Brownie with Fomapan 200

I used Fomapan 200 for the images on this post. Despite the photographs being taken in July, the weather was heavily overcast on the day, and a 400 speed film (or pushing a stop in development) would have been a better choice. The manual states for best results "outdoor exposures should be made with the subjects in bright sunlight", the usual conditions for a typical box camera when these were made; using a faster emulsion allows for a broader range of subject conditions for these cameras than would have been the case when first in use.

Kodak Baby Brownie with Fomapan 200

The one aspect of the Kodak Baby Brownie in use that feels to me not sufficiently thought-through is the position of the shutter lever: placed directly below the lens, this keeps the camera's design symmetrical, with the exception of the winding knob. Here, it feels as though it should naturally be used by the left hand (an illustration in the manual confirms this), and the action of tripping the shutter is to pull it away from the camera's centre of gravity (which must increase the chance of some camera shake). There was a successor to the Kodak Baby Brownie, also designed by Walter Dorwin Teague, though rather less beautiful, in the Kodak Baby Brownie Special. It is notable that the shutter button of the Special is on the user's right, and it pushes in to trip the shutter. The position of the shutter lever on the Kodak Baby Brownie being directly under the lens is also inconvenient when using the time function: the camera does not have a tripod fixing, but the camera's based is fairly flush, allowing for it to be placed on a level surface for long exposures–which makes reaching for the shutter lever less easy–almost any other placement on the camera would be better for this. However, this additional function of the export variant of the Baby Brownie, must make it a little more desirable over the standard model.

Sources/further reading
The Kodak Baby Brownie on Camera-wiki
Baby Brownie on The Brownie Camera Page
On Art Deco Cameras with manual (PDF)
Kodak Baby Brownie on Retro Film Camera
Kodak Baby Brownie on Down the Road
A Camera Worth a Thousand Words Cooper Hewitt

Wednesday, 13 July 2016

127 Day Summer 2016

Vest Pocket Autographic Kodak with Ilford FP4 Plus
For yesterday's 127 Day I shot two new (to me) 127 format cameras: a Vest Pocket Autographic Kodak and the V.P. Twin. I shot 120 film cut down to 127 size, and 35mm Ilford Mark V film taped to 127 backing paper, with both cameras. The Vest Pocket Kodak had problems with light leaks from holes in the bellows which I had been attempting to find and fix the day before; incidentally, both cameras had issues with film flatness, causing some distortions in the negatives, especially with the V.P. Twin, although less noticeable in the shots with the smaller frame size on the 35mm film.

V.P. Twin with Ilford Mark V
V.P. Twin with Fomapan 200
V.P. Twin with Ilford HP5 Plus
V.P. Twin with Fomapan 200
Vest Pocket Autographic Kodak with Ilford Mark V
Vest Pocket Autographic Kodak with Ilford HP5 Plus
Vest Pocket Autographic Kodak with Ilford HP5 Plus

Friday, 13 May 2016

Soho Cadet Model B

Soho Cadet Model B
The materials that cameras have been made from has evolved to suit the technology of image production as it has developed historically. The first cameras were hand built largely from wood, with relatively small volumes of production. With increasing popularity and ease of use, other materials were needed: cardboard for cameras like the cheap Kodak Brownies, metal for smaller, more precise formats which could be cast and machined and produced in greater numbers. Plastic first appeared as a material for camera production in the 1920s (although celluloid was already in use as a base for photographic emulsion itself in the earliest flexible films); notably with the Rajar No. 6, a Bakelite strut-folder made in 1929. Of the early plastics, Bakelite was well suited to camera construction, being easy to mould but hard and rigid once set, and can be drilled and cut. The Rajar No. 6 produced a number of imitators in the 1930s, and, as a material, Bakelite seems to embody Art Deco modernity. However, as other plastics were developed better suited to the task, Bakelite quickly fell out of use for camera bodies, as well as for many other purposes.

The Rajar camera was made by APM which had been formed by the merger of a number of companies largely concerned with the manufacture of film, plates and paper; APM was later split into APEM to continue this line, while cameras were made by Soho. The Soho Cadet Model B clearly owes much of its design to the Rajar No. 6, although it was ultimately derived from the Soho Cadet, a more traditional medium format folding-bed camera from 1930. The Early Photography website dates the Model B to 1931 (other sites give a date of c.1935); the camera itself does not use the name Cadet anywhere, marked simply "Model B" above the lens, but the front and back body sections (as well as some of the metal fixings) appear to be almost the same as those used in the original Cadet: a small amount of alteration may have been made to the Cadet mouldings for the Model B. Instead of the folding bed, the Model B is a strut-folding version with a lens panel not dissimilar to the Rajar No. 6. The back section of the body removes entirely for loading; inside the back is the statement: "Takes any standard film 2 1/4 x 3 1/4 inches or 6x9cms" with the same patent number as that inside the original Cadet (however, Red Bellows describes the Model B as having a different patent number inside). Incidentally, the Rajar camera uses medium format film, but with Rajar's own propriety spool, possibly making the description 'standard film' more apposite than it might at first seem. Frame advance is by red window and there is no pressure plate, which may affect film flatness. Some of the metal parts, such as the two pivoting stands for horizontal and vertical orientation are painted deep maroon to match the Bakelite body and front, the bellows also being maroon too; the remaining metal components are very brightly chromed.

Soho Cadet Model B opened for loading
The Model B has a fixed-focus lens unlike the original Cadet, which could be focussed by the position of the lens panel on the rails of the folding bed. The Cadet was also provided with a (limited) range of shutter and lens options; like the basic Cadet, the Model B has a meniscus lens in an everset shutter with 'I' for Instant and 'B' for Bulb: in bulb mode the shutter fires with the shutter lever tripped in both directions. Although not measured, I estimate that the shutter fires at about 1/40th - and it can sometimes be a little sluggish when the shutter lever is pressed in the down direction: it seems that gravity works against it when held in certain ways. From my rough measurements, the camera has a focal length of around 100mm, making the aperture about f14.

Soho Cadet Model B with vertical stand
My example of the Model B came in a job lot of cameras, and may have been the least interesting of them, but I did want to try it with film. I shot a couple of rolls of Fomapan 200, possibly a stop or two too fast for conditions with bright sunlight, the latitude of the film coped with this well enough. The camera uses a brilliant finder, but one of the smallest I've used, making it difficult to compose a shot. Held vertically, the finder is located directly above the lens behind the lens board, but pivots out through 90 degrees for horizontal shots. The results show all the shortcomings one might expect from a simple meniscus lens: vignetting, astigmatism, barrel distortion, and coma - as well as what appears to be some internal reflection.

Soho Cadet Model B with Fomapan 200
Soho Cadet Model B with Fomapan 200
Interestingly, the lens' curvature of field aberration means that at the very edges of the frame near objects are more in focus: in the image above, the oblique fence recedes away from the lens into focus at the right - but at far left is also in focus. This effect can also seen in the image below in the bottom right. The Soho Cadet Model B is essentially a snapshot camera, no more sophisticated than contemporary box cameras and indeed with less user controls than many. The shortcomings of the lens are a little compensated for by the large image size: this was probably perfectly adequate for contact prints made from the negatives in the 1930s. Today, the camera is probably of more interest of collectors of Bakelite than the film photographer.

Soho Cadet Model B with Fomapan 200
Soho Cadet Model B with Fomapan 200
Sources/further reading
Soho Cadet on Early Photography
Soho Cadet on Red Bellows
Soho on Camera Wiki
Marriotworld's The Bakelite Story